单选题What is the correct configuration of Anycast RP on the loopback interface， assuming a shared anycast address of 10.1.1.1？（）AABBCCDD

题目内容(请给出正确答案)

单选题

What is the correct configuration of Anycast RP on the loopback interface， assuming a shared anycast address of 10.1.1.1？（）

参考答案和解析

正确答案： D

解析：暂无解析

如果没有搜索结果或未解决您的问题，请直接联系老师获取答案。

更多相关问题

第1题

Which two steps are needed when configuring multiple RPs using MSDP within a single PIM domain? ()A. Configure a non-unique address on the loopback interface for use by the PIM RP.B. Configure MSDP with the unique address (router ID) as the local address of the peer.C. Configure MSDP with the non-unique address (router ID) as the local address of the peer.D. Configure a unique address on the loopback interface, used as the PIM RP.

点击查看答案
第2题

What is the default authentication method on an OSPF interface?()A.AB.BC.CD.D

点击查看答案
第3题

You would like to configure an Ethernet interface with the following characteristics:Which set of configuration commands accurately completes this task?()A.AB.BC.CD.D

点击查看答案
第4题

You are trying to recover from a corrupted flash.Which configuration command configures an IP address of 192.168.1.1／24 on the SRP management interface when the ERX1400 router is at the boot prompt?()A.AB.BC.CD.D

点击查看答案
第5题

Which two are correct when configuring an IP address for a Fast Ethernet interface?()A.set interfaces fe-0/0/0 address 10.1.1.1/24B.set interfaces fe-0/0/0.0 family inet address 10.1.1.1/24C.set interfaces fe-0/0/0.0 address 10.1.1.1/24D.set interfaces fe-0/0/0 unit 0 family inet address 10.1.1.1/24

点击查看答案
第6题

The following configuration exists on a router on one end of an IPv6 tunnel. Although the configuration added so far is correct, the configuration is incomplete. Which type of tunnel is most likely to be intended by the network engineer？（）interface loopback 1ip address 192.168.1.1 255.255.255.255interface tunnel 2ipv6 address 2002:C0A8:10 1::1/64tunnel source loopback 1A. Automatic 6to4B. Manually configured tunnelC. ISATAPD. GRE

点击查看答案
第7题

What is the difference between the IPv6 addresses ::／0 and :: ／128? ()A. ::/0 is the default route, and ::/128 is the unspecified address.B. ::/0 is the unicast address, and ::/128 is the anycast address.C. ::/0 is the anycast address, and ::/128 is the multicast address.D. ::/0 is the unicast address, and ::/12 8 is the multicast address.E. ::/0 is the unspecified address, and ::/128 is the multicast address.F. ::/0 is the anycast address, and ::/128 is the default address.

点击查看答案

单选题What is the correct configuration of Anycast RP on the loopback interface， assuming a shared anycast address of 10.1.1.1？（）A AB BC CD D

题目内容(请给出正确答案)

参考答案和解析

更多相关问题

第1题

第2题

第3题

第4题

第5题

第6题

第7题

相关内容